Ghost 2 Immobiliser Reviews
The Ghost 2 immobiliser makes use of modern technology to stop car theft. The device is hidden by thieves and only turns on the engine when a PIN or app is entered.
It connects to the CAN data network in your vehicle and is weatherproof. It also comes with a service/valet mode, which allows you to start your car temporarily while it's in garage for cleaning or servicing.
Easy to install
The Ghost immobiliser is a cutting-edge security device that protects your vehicle from cloning, hacking and key theft. It uses a PIN code system that is integrated into your vehicle's electronic control unit, making it impossible for thieves to identify. Unlike traditional immobilisers, it does not require any special keys or sensors, and is completely hidden with no LED indications or signals to give away its presence. It's also cheaper than replacing an ECU or installing a key fob. It can even lower the cost of insurance.
Follow the directions of the manufacturer when installing a Ghost 2 vehicle immobiliser. This will ensure that the device is working correctly and effectively. Test the system after installation by entering the PIN number and then starting the vehicle. Regular testing will allow you to identify any problems before they get worse.
Check the location of the the CAN H and CAN L wires prior to starting the installation. These are crucial to powering the immobiliser, therefore it is essential that they are properly connected. It is also a good idea to label the wires to make it easier to locate them during the installation process. Once how much is a ghost immobiliser have identified the location of these wires, connect them to a constant 12V power source and a grounding point. Make sure to utilize a fuse tap if needed to protect the connections from short circuits or damage.
After connecting the wires, tidy the wiring using cable ties to stop interference. It is also recommended to cover the wires with insulation tape or heat shrink tubing. This will shield the device from electrical shorts and extend its lifespan. Once the wiring is secured, it's a good idea test the Ghost 2 immobiliser.
In the event that you have to hand over your vehicle, such as for servicing or valet parking for valet parking, the Ghost 2 immobiliser has a service mode that temporarily disables the PIN code sequence. To activate this feature, simply press the brake pedal while pressing the accelerator, and press a number of times that is equal to the first digit of the emergency code. The system will then enter service mode, which can be verified by flashing the indication signal five times.
Change PIN codes with ease
It is easy to protect your vehicle from theft using a ghost 2 immobiliser. It is hidden within the vehicle and can only be accessed using a specific code. The device communicates with the vehicle ECU via its data bus. It does not rely on radio frequency signals as alarm systems that are sold on the market or traditional Thatcham immobilisers do. This makes it difficult for thieves to discern the sound of an immobiliser relay, or to add new key fobs. The control unit is hidden in the vehicle's wiring or dashboard, and cannot be physically tampered to reset the system.
The ghost 2 immobiliser is linked to the vehicle's CAN Data network. It makes use of buttons on the door panels, the steering wheel and the center console, to create a programmable sequence of up to twenty button presses, which must be entered to start the engine - similar as a PIN. This unique next generation system does not require cutting of wires when it is installed and is fully reprogrammable at anytime. You can even put your vehicle in Service or Valet mode to allow it to be started temporarily while you are giving it to a mechanic to work.
You can also use the app to change your PIN code, or deactivate it completely if you've lost your keys. This feature is particularly useful if you've given your car to another person for valet service or parking. It stops them from starting the car and driving it away without your permission. It's also unnoticeable by professional thieves, as it doesn't make use of radio frequencies or circuit cuts.
Another great feature of the ghost 2 immobiliser is its ability to prevent thefts of relays. Relay theft is among the most common methods of car theft. Criminals can hack your car's diagnostic ports and then alter the signal transmitted by the car's ECU to convince it that the car's key is valid and present. The immobiliser of the traditional model is able to be bypassed this manner, but with the ghost 2 immobiliser the signal is blocked by the immobiliser before it gets to the ECU.
Simple to use app
Ghost 2 is an immobiliser that is revolutionary. It protects your vehicle from key-cloning. It connects to the CAN data network of your vehicle and requires a PIN code in order to start the engine. It also deters thieves from using signal spoofing or device spoofing which are common techniques used to steal vehicles.
The system is easy to use and works like an auto alarm that is used in a normal way. Installing the system allows you to create an individual 20-digit PIN code that you must enter prior to starting the vehicle. This will stop the vehicle being stolen, even the case that you lose your keys. You can disable the system with an app for your phone.
The ghost is completely silent and does emit radio frequency signals. It is a quiet weatherproof device that can be positioned anywhere in your vehicle. It can be hidden under the dashboard, door panels or the steering wheel. It communicates with your ECU over the CAN data circuit and is not affected by diagnostic tools that some thieves use to find security systems. It is also not affected by jamming devices that alter codes.
It is a concealed installation that doesn't require any cutting of wires or modifications to the car, and it can be utilized as an anti-theft system for any vehicle. The technology has been proven to be effective and in compliance with TASSA standards. Ghost is a great solution for classic, sports and high-end cars, and it can be used to safeguard vehicles that are let out on websites like Turo.
The Autowatch Ghost 2 represents the next generation of vehicle immobilisers. This system is undetectable to thieves and stops them from starting your vehicle unless they have your PIN or are authorised by the app. It also does not emit any radio frequencies or other signals that could be detected by scanners. The process of installing the app is simple and quick. The app is user-friendly with a simple interface and simple navigation. It also includes a GPS tracker that will help police find the vehicle and locate it.
Simple to reset
A ghost 2 immobiliser is an excellent method to guard your vehicle from theft. ghost immobiliser price integrates with your vehicle's ECU to create a wall that thieves are unable to break through without a valid PIN. The device is also TASSA-certified, which means that it's acknowledged by insurance companies. It's a great device to prevent car theft, and it will save you a lot of dollars in the long run.
The Ghost system unlike traditional alarms and immobilisers that require cutting of circuits it is directly connected to the vehicle's CAN data network. It works by using the buttons on your dashboard and steering wheel. You can create a unique PIN sequence, which can be up to 20 presses in length. This PIN is required to be entered before the engine can start the same way as a credit card PIN. The Ghost system is invisible to thieves and has no LEDs to signal its presence. This makes it the most effective aftermarket CAN-bus immobiliser on the market today.
Another benefit of the Ghost system is that it does not use radio frequency signals, meaning it is not detected or scanned by thieves. This is a deterrent to cloned key attacks and relay attacks, as well as the usual method of hacking into a car's computer system using its CAN bus by searching for signals. Additionally to this, the Ghost system is designed to be completely hidden within the vehicle, and there are no lights or signals that indicate its presence.
The system also has a Transport Mode that disables the Ghost system, which is useful for situations in which you have to temporarily disable it, like when you are traveling or performing maintenance. However, this mode is not as efficient as Service Mode, as it does not disable the system if your vehicle is traveling over 31 mph for 15 minutes.
To reset your ghost 2 immobiliser, you will need to have the emergency code, which you can obtain from your installer. The code is typically hidden beneath the scratch-off portion of the card you received with your installation. This emergency code should be kept safe and stored in a secure location like a wallet at home.